ICE

The ICE bolting system is the culmination of nearly 50 years of research and development dedicated to industrial bolting. Featuring patented industry-first innovations, the ICE is the most advanced hydraulic bolting system available today.

CONTACT YOUR LOCAL SALES REP

Financing Available | Tool Trade In

01. AUTO RELEASE SYSTEM

The ICE can automatically release itself when locked on a bolt. This reduces unplanned interruptions in the bolting process.

02. TOTAL-FREEDOM UNISWIVEL

The ICE is the world’s only hydraulic bolting system that allows for fast and flexible positioning without the constraints normally associated with hydraulic hoses.

03. MULTI-USE SYSTEM

The ICE works with all HYTORC bolting systems including tensioning with the HYTORC Nut and the revolutionary new HYTORC Washer.

SPECIFICATIONS

DOWNLOAD SELL SHEET

Torque Charts Open or Close
- ICE .7
- ICE 1
- ICE 3
- ICE 5

Technical Data Open or Close

Imperial

Metric

MODEL	Height (H)	Width (W)	Length (L)	Radius (R)	Drive	Weight	Torque Range
ICE-1	5.17"	2.18"	4.43"	1.13"	¾"	6 Lbs.	196 - 1,284 ft-lbs
ICE-3	6.58"	2.90"	5.53"	1.52"	1"	10 Lbs.	460 - 3,084 ft-lbs
ICE-5	7.63"	3.80"	6.44"	1.80"	1 ½"	18 Lbs.	804 - 5,360 ft-lbs
ICE-11	9.57"	4.35"	8.35"	2.25"	1 ½"	22 Lbs.	1,800 - 11,743 ft-lbs

Troubleshooting Open or Close
Prior to testing hydraulic torque wrenches. A visual inspection should be done. The visual inspection should include.
1. Cracked, bent, or damaged couplers.
2. Swivel Assembly
  
  Cracked swivel block
  
  Loose swivel assembly
  
  Swivel post retaining ring is attached
3. Loose end cap
4. Cracked or damaged housing
When testing hydraulic torque wrenches. Make sure the pump functions correctly, and is set to 10,000 PSI before the tool is connected. Connect the tool to the hose, and test the tool using the pump remote. ADVANCE and RETRACT the tool several times. Make sure the tool functions properly and the pump pressure builds 10,000 PSI / 700 BAR in the ADVANCE position.
Tool does not ADVANCE or RETRACT. Check the following.
1. Couplers are loose or damaged.
  
  Tighten and/or replace couplers.
2. Ratchet
  
  Replace ratchet if the teeth are stripped, missing or damaged.
3. Drive pawl Assembly
  
  Check drive pawl springs for damage.
  
  Inspect drive pawl for damage.
Tool does not build 10,000 PSI in the ADVANCE position, and there are no external leaks. The tool has an internal leak. Internal leaks are located in two areas, the swivel assembly and the cylinder.
1. Swivel Assembly - Tool will not build over 2000 PSI
  
  Replace damaged swivel seals.
  
  Inspect swivel post for wear and/or damage.
  
  Inspect swivel block for damage.
2. Cylinder - Tool will not build over 6000 to 7000 PSI
  
  Check the piston and cylinder O-ring for wear and/or damage.
  
  Inspect the piston assembly for wear and /or damage.
  
  Inspect cylinder wall for excessive wear.
Tool has an external leak.
1. Swivel Assembly
  
  Bent or broken couplers.
  
  Worn and/or damaged seals.
  
  Cracked or damaged swivel block.
  
  Damaged swivel post.
2. Cylinder
  
  Worn and/or damaged seals.
  
  Loose end cap.
  
  Worn and /or damaged piston assembly.
  
  Damaged housing assembly.
The tool's square drive rocks back and forth. Check the following.
1. Lever Assembly
  
  Lever mounting screws are too tight.
  
  Levers cracked and/or damaged.
2. Reaction Pawl Assembly
  
  Damaged reaction pawl spring.
  
  Damaged reaction pawl.
3. Ratchet
  
  Replace the ratchet if the teeth are stripped, missing or damaged.
Operations Manual Open or Close
- ICE Operations Manual