AVANTI
The Avanti series offers the widest range of torque output with a maximum output of more than 130,000 ft-lbs in the largest model. With tens of thousands in use around the world, the Avanti series is the industry’s trusted solution for next-generation bolting.
CONTACT YOUR LOCAL SALES REP

Financing Available | Tool Trade In
hydraulic wrench

01. REACTION DRIVE

The Avanti features a patented industry-first reaction drive that eliminates the destructive twisting force that occurs in other torque wrenches that have a back-end reaction arm. (*Also found on ICE series)
hydraulic torque
02. TORQUE & ANGLE DIAL
With a simple add-on, the Avanti system is capable of providing a clear angle reading for bolting methods that incorporate turn of the nut.
industrial wrenches
03. MULTI-USE SYSTEM
The Avanti works with all HYTORC bolting systems including tensioning with the HYTORC Nut and the revolutionary new HYTORC Washer for added safety, speed and accuracy on any job.

SPECIFICATIONS

DOWNLOAD SELL SHEET
  • Torque Charts Open or Close
  • Technical Data Open or Close

    Imperial

    Metric

    MODEL Height (H) Width (W) Length (L) Radius (R) SQ Weight Torque Range
    AVANTI .7 4.19" 1.79" 4.14" 0.99" ¾" 3.1 Lbs. 115 - 767 ft-lbs
    AVANTI 1 4.76" 2.18" 4.71" 1.13" ¾" 4.5 Lbs. 196 - 1,284 ft-lbs
    AVANTI 3 6.20" 2.90" 6.15" 1.52" 1" 9.45 Lbs. 460 - 3,084 ft-lbs
    AVANTI 5 7.14" 3.38" 7.36" 1.80" 1 ½" 15.6 Lbs. 804 - 5,360 ft-lbs
    AVANTI 8 7.90" 3.86" 8.24" 1.94" 1 ½" 20.75 Lbs. 1,150 - 7,760 ft-lbs
    AVANTI 10 8.85" 4.35" 9.20" 2.25" 1 ½" 29.20 Lbs. 1,800 - 11,743 ft-lbs
    AVANTI 20 10.22" 5.07" 10.94" 2.60" 2 ½" 47.70 Lbs. 2,760 - 17,890 ft-lbs
    AVANTI 35 12.22" 6.23" 13.45" 3.19" 2 ½" 82.75 Lbs. 4,905 - 31,830 ft-lbs
    AVANTI 50 13.90" 7.04" 16.54" 3.95" 2 ½" 127.7 Lbs. 7,202 - 46,126 ft-lbs
    AVANTI 80 16.84" 7.49" 19.52" 4.69" 3 ½" 280.5 Lbs. 11,965 - 85,695 ft-lbs
    AVANTI 130 19.40" 8.50" 22.73" 5.31" 3 ½" 585 Lbs. 19,395 - 138,510 ft-lbs
  • Troubleshooting Open or Close
    Prior to testing hydraulic torque wrenches. A visual inspection should be done. The visual inspection should include.
    1. Cracked, bent, or damaged couplers.
    2. Swivel Assembly
      • Cracked swivel block
      • Loose swivel assembly
      • Swivel post retaining ring is attached
    3. Loose end cap
    4. Cracked or damaged housing
    When testing hydraulic torque wrenches. Make sure the pump functions correctly, and is set to 10,000 PSI before the tool is connected. Connect the tool to the hose, and test the tool using the pump remote. ADVANCE and RETRACT the tool several times. Make sure the tool functions properly and the pump pressure builds 10,000 PSI / 700 BAR in the ADVANCE position.
    Tool does not ADVANCE or RETRACT. Check the following.
    1. Couplers are loose or damaged.
      • Tighten and/or replace couplers.
    2. Ratchet
      • Replace ratchet if the teeth are stripped, missing or damaged.
    3. Drive pawl Assembly
      • Check drive pawl springs for damage.
      • Inspect drive pawl for damage.
    Tool does not build 10,000 PSI in the ADVANCE position, and there are no external leaks. The tool has an internal leak. Internal leaks are located in two areas, the swivel assembly and the cylinder.
    1. Swivel Assembly - Tool will not build over 2000 PSI
      • Replace damaged swivel seals.
      • Inspect swivel post for wear and/or damage.
      • Inspect swivel block for damage.
    2. Cylinder - Tool will not build over 6000 to 7000 PSI
      • Check the piston and cylinder O-ring for wear and/or damage.
      • Inspect the piston assembly for wear and /or damage.
      • Inspect cylinder wall for excessive wear.
    Tool has an external leak.
    1. Swivel Assembly
      • Bent or broken couplers.
      • Worn and/or damaged seals.
      • Cracked or damaged swivel block.
      • Damaged swivel post.
    2. Cylinder
      • Worn and/or damaged seals.
      • Loose end cap.
      • Worn and /or damaged piston assembly.
      • Damaged housing assembly.
    The tool's square drive rocks back and forth. Check the following.
    1. Lever Assembly
      • Lever mounting screws are too tight.
      • Levers cracked and/or damaged.
    2. Reaction Pawl Assembly
      • Damaged reaction pawl spring.
      • Damaged reaction pawl.
    3. Ratchet
      • Replace the ratchet if the teeth are stripped, missing or damaged.
  • Operations Manual Open or Close

ACCESSORIES

Backup Wrenches Interchangeable spanners from 1-7/16" to 3 1/8".
Sockets High strength and impact resistant hex and Allen sockets.
HYTORC Fastener Drivers High strength Fastener Drivers for the HYTORC Nut and Washer
TORCsafe
Improve your productivity with HYTORC’s preventative maintenance solution for industrial bolting systems.